Lead Shortages Coming - How to Make Your Own Ammo

Poor Man Survival

Self Reliance tools for independent minded people…

http://PoorManSurvivor.net

 

ISSN 2161-5543

A Digest of Urban Survival Resources

 

 

DIY BULLET MAKING

Several months ago I reported that our wise President is closing down the last lead smelting plant inside the United States which will put yet another crimp on ammo for civilians and military alike.  You may want to begin securing supplies of lead now as prices will surely rise as many more preppers and sportsmen will likely step up making their own ammo supply.

What are cast bullets and how are they used, and why would we do that?

Center fire ammo is composed of 4 elements. A bullet (the projectile), the primer, the powder and a brass (usually) casing that hold the other 3 components together. When you shoot a round of center fire ammo, you use the bullet, primer and the powder.  The brass case is left basically intact, and can be reloaded with the other 3 components quite a number of times to mitigate the cost of ammo as well as providing ammo that would be otherwise unavailable. Bullets can be bought, or you can make them yourself, with the right equipment and skills…


Guest Post: by TripodXL

This can’t be an encyclopedic instruction manual for making cast bullets, which will become obvious. There are 4 basic needs for bullet casting. You need lead, bullet molds, a lead furnace and casting tools, and sizing/lubricating equipment.

First, by further reading this information, the user AGREES that this information is used at the user’s own risk and the user accepts ALL RESPONSIBILITY for engaging in any activity related to this information. This information is given as general guidelines for the purpose of discussion and is in no way intend to be complete, all encompassing on the subject, and is not warranted to be accurate or applicable to all situations of its’ use. This activity deals with toxic substances, dangerous circumstances and potentially life threatening consequences. THE USER ACCEPTS ALL RESPONSIBILITY.

Lead is obtained a number of ways. You can buy lead from metal suppliers, and this is probably the most expensive way to obtain it, but may be the only way. You can go to your local tire center and ask if you can have their discarded wheel weights. You will usually still have to buy them and you will need to find out what a fair price is. There is a caveat, depending on where you live. They may have to turn them in to a recycler by law. If your state is that way you will have to determine how to get them, or you may just get them at the metal recycler to begin with and not have to drive around looking for them. This is actually the best way to get them.

If you get wheel weights they are acceptable “as is” for bullet alloy. Most folks don’t realize that pure lead makes crappy bullets as it is too soft (except for muzzle loading) and will cause leading in firearms.  The lead actually builds up in the rifling of a barrel and causes a significant decrease in accuracy.  If you are lucky enough to have a few tons of leaded drywall around, it is pure lead and will have to be alloyed, but even wheel weights can benefit from having some other metals added to it. If you want complete Q/C over your alloy, it would be best to buy it and mix it or buy a standard alloy. If you are going to cast bullets, I would suggest that you get a Lyman “Cast Bullet Handbook”. The current edition is the 4^th and is not as good as earlier editions.

Bullet molds are the next thing you need. You will have to decide, if you are going to shoot them from a handgun or a rifle, are they going to be hot magnum loads or more of a “standard” velocity for practice?

  There are two kinds of molds, aluminum and cast iron. Both have their place and you have to use both to learn the differences. Aluminum is cheaper, and easier to tear up, but it is easier to start casting good bullets with. Iron is more durable but it is a PITA to keep the temps right and cast good bullets with.  Lee makes aluminum molds that are cheap and are good starter molds and if you tear one up you don’t have $100+ invested in it. Learn on them before you buy higher quality, higher priced molds. RCBS, Lyman and other companies make great iron molds. NEI (North East Industrial) makes the best aluminum molds of a higher quality than any other I have tried. I have 6 and I like them. They are not like the Lee molds.  They are harder and more durable than Lee, so don’t use them as a guideline for not using aluminum molds.

You need one or two bullet designs and stick to them after you get your learning curve down. Buy “gang molds” where you cast 2,4,6 or more bullets with one pour. A four gang mold won’t cost much more than half again as a single cavity mold and quadruple your casting rate. If you are shooting, slow to moderate velocity handguns, straight wheel weights will be hard enough. For magnum speed handgun loads you will need a harder alloy, which will require some added tin and antimony (you’ll figure it out).

 Rifles and really high-speed loads will require the very hardest alloy with something called a gas check pressed onto the base of the bullet. The bullet is cast with a step at the base and a round copper “cup” is pressed onto the base (like a scraper) so that the higher speeds won’t lead the bore of the firearm. There are speed limitations of about 2200 fps for gas-checked lead rifle bullets. You can’t duplicate full speed rifle loads, and lead bullets should not be used in semi-automatic rifles.

You will need equipment to melt and alloy the lead. Electric furnaces that you can buy have heat controls on them, or you can find an old, HEAVY, IRON dutch oven and use a good propane burner and melt the lead/alloy that way. DON’T EVER USE THE DUTCH OVEN FOR FOOD. Make sure you have good ventilation if you are inside and using a furnace. If you are using the LP burner method, you can be under a roof, if high enough, BUT DON’T DO IT IN AN ENCLOSED SPACE. I recommend doing it under cover as molten lead and liquids don’t get along and while it might not rain a big gob of bird crap will cause quite an explosion (how do I know that).

Regardless of which method you use (I use both, I use the dutch oven to feed my electric furnaces) you should have an accurate lead thermometer because the casting temp is crucial to getting good bullets.

You will need some special equipment for processing your bullets. Cast bullets are slightly oversized, so you have to “size” them by pressing them through a “sizer die”. You can buy a cheap little punch and a sizer die, and tap them through with a hammer. In the beginning, this is what I recommend for learning and it won’t cost much.  Then you need to lube the bullets to prevent leading. When I started, I would size them in my little cheap sizer, then put all my bullets in a flat pie tin and pour melted bullet lube into the pan up to the lube grooves of the bullets. After it hardened I would cut them out with a little tool called a “cake cutter” and have bullets ready to go. When you have decided that you want to do this at a higher level that is quicker and more efficient you can buy a “lubri-sizer” which is a press that pushes the bullets through a size die and lubes it at the same time and they fall out the bottom into your bullet bucket, as fast as you can put them in.

As you can see this isn’t just a cookbook type skill. Good bullet casting is more of an art, but not too hard to learn. I learned it out of a book and taught myself, forty years ago. I have taught it to many others so they didn’t have to learn it the hard way, but you can learn it yourself if there are no mentors around. Use the proper PPE (gloves, eye protection, shop apron, etc.) when working with any of this at any stage. Also, do not eat or drink while engaging in any of this activity.

As you can see this only popped the lid off this topic but bullet casting and reloading can save you money through sweat equity and allow you control over a lot of your ammo destiny.

 

http://modernsurvivalblog.com/security/how-to-make-cast-lead-bullets/

http://www.zjstech.net/gunstuff/casting.html

 

 

More useful tidbits to use and share!

64 "Fabulous" Freebies

Here is Kiplinger's annual list of "fabulous freebies." Some are more "fabulous" than others, however. We apologize for having to view this list in slideshow format -- that is the only way they offer it.

http://content.kiplinger.com/slideshow/saving/T063-S001-fabulous-freebies-2012-slide-show/index.html

 

Best Ways to Sell the Stuff You Don't Need

If it is time to declutter or you are thinking about upgrading, Consumer Reports tells you how to maximize the dollars you'll get for your old stuff.

 

DIY-The Dakota Fire pit, a classic survival cooking unit:

Dig a vertical column 1 foot deep by 1 foot wide.  Move 18” upward and carve a 6x6 inch air vent diagonally to connect at the base of the large hole.  As the hot air escapes the main hole it draws air through the other end of the tunnel.  This constant cycle of air makes the fire hotter and saves on wood.

 

RAISE YOUR OWN EDIBLE CRICKETS

For those interested in harvesting a food supply within a small space, you might consider the protein packed cricket.  Learn how to breed and raise them yourself at:

Popsci.com/eatcrickets

 

How baby boomers can reduce food waste
read more here

 

Find DIY and Homemade ideas here:

http://www.poormansurvival.com/Pages/Homemade.aspx                                           

 

 

Gunsmithing at Home

Diagnose and repair a broad selection of popular hunting firearms in the convenience of your home workshop and save money, too.

http://www.bonanza.com/listings/Gunsmithing-at-Home-New/176936271

 

Your donations and purchases are appreciated…

Yours in freedom,

Bruce ‘the Poor Man’

 

Got a News Tip or Resource to Share With the Poor Man?

Send it to:  PoorManSurvivor@Gmail.com

 

Our Mission: To protect and promote your freedom, civil rights, financial well being and overall self reliance in these turbulent times.   Get more tips and freebies at: www.PoorManSurvival.com

A Shallow Planet Production